diff options
Diffstat (limited to 'net/yate-devel/files/README.too')
-rw-r--r-- | net/yate-devel/files/README.too | 161 |
1 files changed, 161 insertions, 0 deletions
diff --git a/net/yate-devel/files/README.too b/net/yate-devel/files/README.too new file mode 100644 index 000000000000..ae066f288a25 --- /dev/null +++ b/net/yate-devel/files/README.too @@ -0,0 +1,161 @@ +Asterisk Open PBC/IVR Project using the Sangoma A101 and A102 cards +=================================================================== + +Alex Feldman: Aug 10 2005 +Nenad Corbic: + +WANPIPE supports the Asterisk Open PBX/IVR project through an interface +of the Zaptel family of hardware devices. These devices share a common +driver suite, called the ZAPATA Telephony Driver Suite (zaptel). + + +ASTERISK / ZAPTEL Installation +------------------------------- + +First install: + zaptel, and asterisk software on your system. + +The Zaptel module can be installed using one of the following methods: + +1. You can use ports collection or packages method of installation if you + want to install the latest stable release: + # cd /usr/ports/misc/zaptel/ + # make install + +2. You can also use nightly snapshot from sn repository + (http://www.portaone.com/~gonzo/zaptel-bsd-trunk.tar.gz). + +3. Subvestion repository: https://svn.bluezbox.repos/zaptel-bsd + svn co --username svn --password svn https://svn.bluezbox.com/repos/zaptel-bsd + +The Asterisk application can be installed from ports collection: + # cd asterisk + # make install + + + +WANPIPE Releases +---------------- + +2.8.2-1: Latest Wanpipe Release + + o First version of Sangoma driver for FreeBSD OS that + support Asterisk/Zaptel interface (AFT-A101/A102/A104 cards Only) + + + +WANPIPE Installation for Asterisk +--------------------------------- + +1. Download the LATEST Wanpipe 2.8.2 Release or Greater! + + Note: Wanpipe does not support Asterisk in releases + LOWER than 2.8.2! + + ftp.sangoma.com/FreeBSD/current_wanpipe + + +2. Install WANPIPE package + + eg: pkg_add wanpipe-2.8.2-1.tgz + + + Proceed with default installation options. + + IMPORTANT: + Under compilation mode: select CUSTOM + + Then select: DEF :for default protocols + TDM :for TDM Voice asterisk support + + Proceed to compile wanpipe drivers. + +4. To confirm successful installation run: + + wanrouter hwprobe + + Confirm that Sangoma cards have been found. + + Note: + Zaptel kernel drivers must be compiled and installed + BEFORE loading WANPIPE drivers. + + +WANPIPE Configuration for the A100 series of cards +-------------------------------------------------- + +You can use the A101/A102 or A104 cards for both data and voice. +The following describes how to configure the Asterisk system for +voice, with an auxiliary data interface, if needed. + +1. Run the configuration utility wancfg. + + /usr/sbin/wancfg + + Hardware Setup: + Select Hardware: AFT + + T1/E1 CSU/DSU Setup can be configured via + "Advanced Physical Medium Config" + + Protocol Setup: + Select Protocol: TDM VOICE + No other options + + Interface Setup: + Select: SPAN Number: 1-24 + The SPAN usually starts with 1 + + Select: Override Asterisk Echo Enable + Default: NO + + This optoin will DISABLE/Override Asterisk + ECHO Cancellation Cfg for this SPAN. + + Therefore, if you want to DISABLE Echo Cancellation + for this SPAN, ie: ignore what is configured in + zapata.conf, then set this option to YES. + + Used in switching applications where single SPAN + needs echo cancellation and rest do not. Therefore, + one would use this option to disable ECHO + cancellation on SPANS that don't need it. + + +Zaptel configuration +-------------------- + +Download the documentation how to configure Zaptel driver from + +(http://www.digium.com/downloads/configuring_zaptel.pdf). + +When configuring the Zaptel driver (/etc/zaptel.conf) + + 1) Select the same span configurations as you used for WANPIPE + (i.e. LBO, framing, coding parameters). + + Otherwise the Zaptel configuration is completely + standard, except that if there are data channels that + will be handled by WANPIPE, those channels should be ignored, + and not configured as 'nethdlc'. + + 2) If you are using multiple WANPIPE devices for Asterisk + + For example, an A102 card might be configured as: + + wanpipe1 and wanpipe2 + + then you need to set your starting scripts to start + the wanpipes in the same sequence as defined in zaptel.conf. + + Run: wanrouter wanrc + + to set the wanpipe startup order. + + 3) If you are using some channels for DATA + + You don't need to set the channel list for this + interface under /etc/zaptel.conf because all data will go + through the separate WANPIPE driver to the kernel. + +------------------------------------------------------------------- |